Live stream from an Android phone to a channel of your own

To live stream from an Android phone to your own channel, install an RTMP app such as Larix Broadcaster, add a connection with your channel's server address and stream name, and press the big red button. By the end of this guide you will have a phone on a stand sending a steady picture to a link your viewers can open in any browser, plus a plan for the two things that end most phone broadcasts early: a hot phone and a flat battery.

By the Stream Brothers team

Every step was checked against the software's official documentation by independent reviewers before publishing. Last reviewed .

Before you start

Running order
  1. Gather these four things first
  2. Which settings can my phone really hold?
  3. Connect Larix to your channel, step by step
  4. Keep the phone cool and charged
  5. Will my connection stay steady?
  6. Rehearse before the real broadcast
  7. When a phone is not the right tool
  8. Your questions

Gather these four things first

You need four things: an Android phone, an app that speaks RTMP, a channel to send to, and a place to plug the phone in. RTMP (Real-Time Messaging Protocol) is simply the language most streaming apps use to hand live video to a server.

  • A phone on Android 7.0 or newer. That is the minimum Larix Broadcaster lists for its Android app.
  • Larix Broadcaster. Our live video names it alongside OBS Studio, vMix and Wirecast as a sender it takes, and it publishes over RTMP to any standard receiving server. An encoder is the app that compresses your camera picture into a stream.
  • A live channel. Our live video channels take RTMP in and play it back as HLS, a format that runs in any modern browser on phones, tablets, computers and smart TVs, so your viewers need no app at all.
  • A charger or power bank and a stand. A tripod clamp keeps the picture still and leaves your hands free.

Which settings can my phone really hold?

Start at 720p and 30 frames a second with the H.264 codec, which is the starting point Softvelum, the maker of Larix, suggests for testing before moving up. Resolution is the size of the picture; bitrate is how much data per second the stream uses, and it is what your upload has to carry.

PictureLarix's matching bitrateWhen to use it
720p, 30 fps2000 kbpsYour first broadcasts, mobile data, busy Wi-Fi
1080p, 30 fps3000 kbpsA strong, tested line and a phone that stays cool

Those bitrates come from the table Larix uses when you switch on its Bitrate matches resolution option; on Android you can also type your own value. Two limits from Softvelum's notes are worth knowing. Most Android phones let outside apps such as Larix use 1080p at 30 frames a second, but 60 frames a second is not guaranteed because many devices do not offer it to outside apps. Our Pro and Platinum channels accept up to 1080p at 5 Mbps, so a phone's sensible settings sit comfortably inside what the channel takes.

Many phones encode in VBR (variable bitrate) by default, and Softvelum notes that in that mode Android can go above a low bitrate you set. Leave some headroom on your upload rather than setting the bitrate right at its limit.

Connect Larix to your channel, step by step

Your channel gives you a server address and a stream name for your encoder, and some channels also have a publishing login. Have them open on a computer, or copy them to the phone, before you begin.

  1. Install Larix Broadcaster and open it. Allow it to use the camera and microphone when Android asks.
  2. Tap the gear button to open the settings screen, choose Connections, then tap New connection.
  3. Give the connection a name you will recognise, such as the name of your channel.
  4. In URL, paste the server address, then a slash, then the stream name. Larix takes the whole target as one line, so the address and the name go together in this one field.
  5. If your channel shows a publishing login, type it into Login and Password. If it shows none, leave both empty.
  6. Press Ok to save, then go back to the camera screen.
  7. Turn the phone sideways. If your version of Larix offers it, set the orientation to Always horizontal so a twist of the wrist does not flip the picture.
  8. Press the big red button. Your player link should show your picture after a short delay.

If nothing arrives, check the URL first: a missing slash or a stray space at the end is the usual culprit. Then check that the phone is online and that the login matches.

Keep the phone cool and charged

Plug the phone in for the whole broadcast: Softvelum warns that streaming at high quality drains a battery fast, and recommends a good power bank or a charger. Heat is the other half of the same problem, because a phone that is encoding video, using the radio and charging all at once gets warm.

  • Switch off live rotation and image overlays in Larix if you do not need them. Softvelum names both as extras that cost power and add heat.
  • Take the phone out of a thick case and keep it out of direct sun.
  • Leave Battery Saver off during a broadcast. Android's own help says it limits or turns off background activity and can delay network connections, which is the opposite of what a live stream needs. It lives under Settings > Battery > Battery Saver, though the name and place vary by phone maker.
  • Turn on Do Not Disturb so calls and notifications do not interrupt you. On recent Android versions it is under Settings > Modes > Do Not Disturb, or in Quick Settings when you swipe down from the top of the screen and tap Do Not Disturb.

Will my connection stay steady?

It will if your upload speed comfortably beats your bitrate in the exact spot where you will stand, so measure there, not at your desk. Our guide to upload speed for live streaming walks through measuring it and what to turn down first when the line falls short.

Larix can also lower the bitrate on its own when packets go missing, a feature called adaptive bitrate. For RTMP it offers two modes:

  • Logarithmic descend steps the bitrate down gradually from your maximum and tries to raise it again every minute. Softvelum suggests it for good networks.
  • Ladder ascend first cuts the bitrate by two thirds, then climbs back in steps. It suits networks with heavy losses, such as a crowded venue on mobile data.
  • An optional Variable FPS setting also lowers the frame rate, which cuts the bitrate further when the line is very poor.

Prefer Wi-Fi you control over mobile data where you can, and keep the phone close to the router. Larix also supports SRT, a protocol built for unreliable networks, but your channel takes RTMP, so use an RTMP connection for it.

Rehearse before the real broadcast

Do a full run-through for longer than the event itself: Softvelum's advice is that a one-hour event deserves a two-hour test. Move the camera, change the scene and watch the phone's temperature as the time passes.

  1. Use the Free plan if you are just starting out: it exists to test your encoder and player, for up to 10 viewers at a time.
  2. Open the player link on a second phone using mobile data, so you see what a viewer sees.
  3. Once it runs cleanly, stop changing apps and settings until the event is over. Softvelum recommends freezing everything after testing and retesting after any change.

On Pro and Platinum your channel does not go dark between broadcasts: the TV station plays videos from your library around the clock, so viewers who arrive early see something other than a blank player.

When a phone is not the right tool

A phone is one camera and one microphone, and it is at its best for a single view: a sermon, a lecture, a small gig, a sideline. If you need several cameras, titles and a score on screen, a laptop running OBS Studio is the better encoder, and our high school football guide shows that kind of setup.

If the phone overheats in a long test even with the extras switched off, drop to 720p rather than hoping for the best on the day. And if you plan to send the same picture from a laptop later, our guide to OBS dropped frames will help you read what the encoder is telling you.

Start your channel and go live from your pocket

Set up a channel, paste its address into Larix and test your first broadcast on the Free plan before the big day.

Your questions

Do my viewers need to install anything to watch?

No. Your channel plays as HLS in an embeddable player that runs in any modern browser on phones, tablets, computers and smart TVs. You share the link or put the player on your website, and people press play.

Can I stream from my phone on mobile data instead of Wi-Fi?

Yes, as long as the upload speed where you stand is clearly higher than your bitrate. Start at 720p and turn on Larix's adaptive bitrate so it can step down when the signal weakens. Measure the speed on site before the event, because mobile signal changes from room to room.

How long can a phone stream before it gets too hot?

It depends on the phone, the room and your settings, so there is no single answer. The way to find out is an endurance test at least twice as long as your event, with the phone plugged in and the extras such as overlays and live rotation turned off. If it struggles, lower the resolution.

Is 1080p from a phone worth it?

Only if the phone offers it steadily and your upload can carry it with room to spare. Most Android phones reach 1080p at 30 frames a second, and Larix pairs that with a higher bitrate than 720p. A steady 720p picture is kinder to viewers than a 1080p one that keeps pausing.

What if I get stuck setting up the connection?

Pro and Platinum include help by phone and live chat, day and night, and the Free plan includes help by email. You can also open a ticket from the support page and describe what Larix shows when it fails to connect.