Multi camera live streaming: switch two or three cameras without a TV truck

Multi camera live streaming means every camera feeds one switcher, either OBS Studio on a computer or a small hardware box, and only the picture you pick leaves the building, so three cameras need no more upload than one. By the end of this guide you will have two or three angles you can cut between with one click, sound that stays on the lips, and a single link your audience opens on any phone.

By the Stream Brothers team

Every step was checked against the software's official documentation by independent reviewers before publishing. Last reviewed .

Before you start

Running order
  1. The kit for a two or three camera stream
  2. Software switching or a hardware switcher?
  3. Switching cameras in OBS Studio, step by step
  4. Switching with a small hardware box
  5. Keeping the sound in sync with every camera
  6. How much upload does each extra camera need?
  7. When three cameras is too many
  8. Getting the finished picture to your audience
  9. Your questions

The kit for a two or three camera stream

You need cameras, a way to bring each one into your switcher, one good sound source and a channel to send the finished picture to. Most first setups grow from a single camera, so if you have not streamed with one yet, our guide to streaming a football game with one camera is a gentler place to begin.

  • Two or three cameras. Camcorders or mirrorless cameras with a clean HDMI output, USB webcams, or phones running a camera app.
  • A way in for each camera. A USB webcam plugs straight into the computer. An HDMI camera needs either a USB capture card (a small adapter that turns HDMI into something the computer sees as a webcam) or a hardware switcher with HDMI inputs.
  • One sound source. A microphone or the output of the sound desk. More on this below; it matters more than the cameras.
  • A channel. A live video channel takes the stream from your software over RTMP (the way an encoder hands live video to a server) and plays it to viewers in any browser.

Software switching or a hardware switcher?

Switch in OBS Studio if you already have a capable computer and want to keep spending low; add a hardware switcher when you want physical buttons, HDMI cameras without a capture card each, or less load on the computer. Both end at the same place: one finished picture sent to your channel.

OBS Studio on a computerSmall hardware switcher
How cameras connectWebcams by USB; HDMI cameras through one capture card each; phones through an appHDMI cameras straight into the box (the ATEM Mini Pro has four HDMI inputs)
How you switchClick a scene, or a hotkey you setPress the input button: CUT for an instant change, AUTO for a transition
Mixed camera settingsEach source is scaled into your canvasInputs are standards converted, so the cameras need not match
Load on the computerEvery camera is decoded and composited by the computerThe box mixes; the computer sees one webcam, or none at all
Getting it onlineOBS streams to your channelInto OBS as a webcam, or direct over Ethernet on the Pro models

The ATEM details come from Blackmagic Design's specifications for the ATEM Mini Pro; check your own model's manual.

Switching cameras in OBS Studio, step by step

In OBS each camera gets its own scene, and switching cameras means switching scenes.

  1. In the Scenes box, click + and name the first scene after its angle, for example Wide. Scene and source names are shared across OBS, so give each one a different name.
  2. With that scene selected, click + under Sources, choose Video Capture Device, and pick the camera or capture card from the Device list. You should see its picture in the preview.
  3. Repeat for Close and Side, one scene per camera. Set your microphone or sound desk under Settings → Audio as a global Mic/Auxiliary Audio device, so it is heard whichever scene is live.
  4. Click Studio Mode. The left side becomes the shot you are lining up and the right side is what viewers see.
  5. Pick the next scene on the left, then press Transition to send it live. Cut and Fade are there from the start; keep transitions short so the change feels natural.
  6. Optional: open View → Multiview (Windowed) to see every scene at once, and set hotkeys under Settings → Hotkeys so a key press switches shots.
  7. Connect OBS to your channel under Settings → Stream, using the server and stream key from your channel dashboard.

The Video Capture Device setting Deactivate when not showing saves resources, but the OBS guide notes the picture can go blank for a moment while the device wakes up again. For cameras you cut between live, leave it off.

Switching with a small hardware box

A hardware switcher takes the camera work off the computer: you plug HDMI cameras into it, press a button for each shot, and it hands one clean picture onward. Blackmagic's ATEM Mini range is one example, and its getting-started guide covers the basics.

  1. Plug each camera into an HDMI input. The inputs convert formats, so a camcorder and a mirrorless camera can sit side by side.
  2. Press an input button to cut to that camera. Press AUTO first if you want the change to use a transition.
  3. Connect the switcher's USB-C port to your computer. The computer sees it as a webcam, so in OBS you add it once as a Video Capture Device and stream as usual.
  4. On the ATEM Mini Pro, plug your microphone into one of the two 3.5 mm audio inputs, or bring sound in through OBS from the desk. Pick just one of those routes, or you will hear an echo.

The Pro and Extreme models can also stream by themselves over Ethernet, picking a service and server in ATEM Software Control. Going through OBS as a webcam is the simplest route to a channel of your own.

Keeping the sound in sync with every camera

Take all your sound from one place and let every camera be picture only; that single choice prevents most sync trouble. Camera microphones sit at different distances, so cutting between them makes the voice jump with every shot.

  • Mute the camera audio. In the OBS Audio Mixer, click the speaker icon on each camera's sound to mute it.
  • Clap to check. Before the event, send a test stream to your channel, clap once in front of each camera and watch it on a phone: the sound and the hands should meet.
  • Sound arrives before the picture? Open Edit → Advanced Audio Properties and raise the Sync Offset for your microphone a little at a time until the clap lines up.
  • Picture arrives early? OBS has a Render Delay filter that holds a video source back to match the sound.
  • On the ATEM Mini Pro, the 3.5 mm inputs can be delayed by up to 8 frames, which covers small gaps before the signal reaches the computer.

Judge sync the way your audience will: on a phone playing the real stream from your channel, not in the OBS preview or your headphones.

How much upload does each extra camera need?

None, as long as the switching happens on site: the switcher picks one picture and OBS encodes only that, so three cameras send exactly what one camera would. Bitrate (how much data per second the stream uses) is set once in OBS and is the same whichever angle is live.

Your channel accepts up to 5 Mbps at 1080p on the Pro and Platinum plans, and your connection must carry that comfortably. Our guide to upload speed for live streaming shows how to measure the line you will really use. Phone cameras that join over Wi-Fi or NDI use your local network, not your internet upload, but they need a steady connection; the OBS documentation notes that NDI output is picked up automatically by receivers on the same local network.

Platinum runs two channels at once, for parallel rooms, venues or a backup feed. That is the one case where you send two streams, and so need upload for both.

When three cameras is too many

Add cameras only as fast as your computer and your crew can handle them. Every camera in OBS is more work for the processor, and an overloaded computer drops frames that no upload speed can fix; our guide to OBS dropped frames explains how to tell which kind you have.

  • Capture cards that drop out. If a camera flickers or vanishes when you plug in the next one, try a different USB port, or move the HDMI cameras onto a hardware switcher.
  • One person can not frame and switch at once. A camera nobody is watching tends to drift; a locked-off wide shot is better than a wandering close-up.
  • Rehearse. A full run-through the day before, sent to your channel and watched on a phone, finds the problems while there is still time.

Getting the finished picture to your audience

Once your switcher sends one stream, the live video channel does the rest: viewers get an HLS link and an embeddable player without ads that plays on phones, tablets, computers and smart TVs. The Free plan lets you test your encoder and player with up to 10 viewers at a time, which is exactly what a rehearsal needs. Pro opens the channel to 1,000 viewers at once, with traffic not counted, and its 24/7 TV station keeps your channel playing from your video library between live shows.

Stuck on the night? An AI chat assistant can inspect your channel at any hour, a human can take over whenever you ask, and Pro and Platinum add phone and live chat support.

Put your cameras on air

Start with a free channel to rehearse your switching, then open it to your whole audience when the shots are ready.

Your questions

Can I mix a webcam, a camcorder and a phone in one stream?

Yes. OBS treats each one as a source in its own scene, and a hardware switcher's HDMI inputs convert different formats for you.

Do I need a hardware switcher to stream with two cameras?

No. OBS Studio can switch cameras on any computer that keeps up, with Studio Mode showing the next shot before it goes live. A hardware switcher is worth having if you want physical buttons, several HDMI cameras without a capture card each, or less work for the computer.

Why is my voice out of step with the picture after I added a capture card?

Each capture card or switcher in the path can hold the picture back slightly, while a microphone plugged straight into the computer does not. Raise the Sync Offset for the microphone in Edit → Advanced Audio Properties, check with a clap, and repeat until it lines up.

Will viewers notice when I switch cameras?

Only the cut itself. The stream keeps the same bitrate and size whichever camera is live, so the picture does not pause or reload.

Can I use a phone as my second camera?

Yes. The OBS documentation lists several apps that turn a phone into a camera over USB or Wi-Fi, and browser-based options that come in as a Browser Source. Keep it on a stand and on charge.