Your kit for a one-camera briefing
A press conference is among the gentlest events to stream: people stand still, one person talks at a time and the room is lit. Here is the short kit list and what each piece is for.
| Item | What it does | Tip |
|---|---|---|
| Camera on a tripod | Frames the podium and the backdrop | A camera with a clean HDMI output into a capture card, or a good webcam |
| Audio feed from the podium | Carries the speakers' voices without room echo | Ask the venue's sound person for a line out of their desk |
| Audio interface | Turns that feed into an input the laptop can use | A small USB box is enough; bring headphones |
| Laptop with OBS Studio | Mixes picture, sound and slates, sends the stream, records | The encoder used in every step below |
| Wired internet | Carries the stream out of the building | Ask for an Ethernet port; the venue Wi-Fi is shared with every reporter's phone |
| A video channel | Turns your stream into a link anyone can watch | Gives you the player code newsrooms embed |
OBS Studio calls the camera a Video Capture Device source, which takes a webcam, a capture card or another video device. For a single-camera briefing you need neither a video switcher nor a second operator.
Will the venue's connection carry it?
Only a test in the room itself, on the exact port you will plug into, can tell you. Upload speed is what counts here, because your laptop pushes video out rather than pulling it in. Our guide on measuring upload speed for streaming explains how to check it and what to turn down first when it falls short.
Bitrate means how much data per second your stream uses. A paid channel accepts up to 5 Mbps at 1080p, so keep OBS at or below that and leave spare capacity on the line for everyone else in the building. A speaker at a podium stays sharp at a modest bitrate because so little in the picture moves.
Visit at the same time of day as the event if you can. A line that tests well in an empty hall can struggle once the room fills with reporters sending photos and clips.
How do I get clean sound from the podium?
Take the sound straight from the venue's mixing desk rather than from the camera's microphone. Viewers forgive a soft picture far sooner than a hollow, echoing voice, and reporters quoting the speech need every word.
- Ask the sound person for a line-level output from their desk and run it to your audio interface.
- Plug the interface into the laptop. In OBS open Settings, then Audio, and choose the interface as a microphone or auxiliary device.
- Mute the camera's own microphone in the Audio Mixer with its speaker icon, so only one copy of the voice goes out.
- Have someone speak at the podium. Speech should sit high in the yellow zone of the meter and only brush the lower edge of the red, which OBS describes as close to clipping.
- Put headphones on and switch on monitoring under Edit, then Advanced Audio Properties, so you hear exactly what viewers hear.
If the feed arrives in one ear only, tick Downmix to Mono for that source in Advanced Audio Properties so phone viewers hear it from both speakers.
Build your holding slate and live scenes
A holding slate is a still picture telling early viewers what they are waiting for. OBS keeps each look as a scene, and you click between them. Three scenes see you through the whole briefing.
- In the Scenes dock, click the plus sign and name the first scene "Starting soon".
- In the Sources dock, click the plus sign, choose Image and pick a picture with your logo, the subject and the start time. It should fill the preview.
- Add a scene called "Live" holding your Video Capture Device and the audio feed. Check the speaker has headroom and the backdrop logo shows.
- If you like, add a text source with the speaker's name and role along the bottom of the Live scene, and hide it with the eye icon after the first minute.
- Add a scene called "Thank you" with an image saying the briefing has ended and where the replay will be posted.
Go out on the holding slate fifteen minutes early. Newsrooms can confirm their embed works before the speakers arrive, and you are not rushing when the room falls quiet.
Connect OBS to your channel and rehearse
Your channel takes RTMP, the common way encoders such as OBS Studio, vMix, Wirecast, Larix or a hardware box send live video to a server.
- Run Tools, then Auto-Configuration Wizard, on the venue's line so OBS can suggest settings for your laptop and connection.
- In Settings, then Stream, choose Custom as the service, then paste your channel's RTMP server address into Server and its key into Stream Key.
- In Settings, then Output, keep the video bitrate within the 5 Mbps your channel accepts.
- Click Start Streaming with the holding slate up, then load your player on a phone that uses mobile data. The slate should appear after a short delay.
- Switch to the Live scene, talk at the podium for a few minutes and listen on the phone for gaps or crackles.
If the picture stutters in rehearsal, our guide to fixing OBS dropped frames helps you tell a network problem from a laptop that is working too hard.
Give reporters a link they can embed
Each channel comes with an HLS link and an ad-free player that goes into a web page with a single line of code. HLS is the stream format browsers on phones, computers and smart TVs already play, so nobody installs an app.
- Place the player on a press page of your own site ahead of time. Without a site yet, website hosting with free SSL gives that page a home.
- Put the embed code in the media advisory, with the start time and a contact for technical questions.
- Keep the address short enough to read out. A name from domain registration suits an organisation that holds regular briefings.
- Warn reporters that a holding slate runs until the start, so nobody assumes the stream is broken.
The player carries only your channel, and viewer traffic is not counted, so a briefing that travels widely never comes back as a bill for traffic.
Keep the recording for the replay
Record on your laptop while you stream, because live broadcasts are not saved into your channel's video library. OBS does both at once, and picking Same as stream for recording quality avoids extra load on the laptop.
- In Settings, then Output, set a Recording Path on a drive with lots of free space.
- Set the Recording Format to MKV. OBS's recording guide recommends it because a recording cut off by a crash or power cut is not lost as a whole. (Newer OBS versions start new profiles on Hybrid MP4, which also guards against this.)
- Click Start Recording the moment you go live and check the timer is running.
- If you recorded in MKV, use File, then Remux Recordings, afterwards to turn the file into an MP4 that editors and websites accept.
On Pro and Platinum you can upload the finished file to the channel's library so the replay sits beside the live feed, and the channel's TV station plays your library between broadcasts instead of going dark.
Which plan fits, and when this setup is not enough
Free is for testing your encoder and player: 10 viewers at a time suits a rehearsal, not a real briefing. Pro gives one 1080p channel for 1,000 simultaneous viewers, a 50 GB library and phone and live chat help day and night. Platinum adds a second channel for a backup feed or a parallel room, a 200 GB library and delivery from the nearest of five cities. Compare them on the live video streaming plans page.
- Expecting more than 1,000 people at the same moment? This setup alone is the wrong fit.
- Remote reporters asking questions on camera need a video-call tool beside the stream; the channel is a one-way broadcast.
- Several camera angles and graphics call for a second person on OBS while you watch the room.